Beschrijving
Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack is een plug en play oplossing voor je race drone. Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack met zijn 20x20mm en 30A esc zijn in staat om 5” propellers te ondersteunen. De Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack beschikt over veel vermogen en performance in een super kleine afmeting en is eenvoudig. Geen moeilijke verbindingen met de 32bit 30A 4in1 ESC en de F4 OSD Flight Controller maar simpel op elkaar klikken. De 4 motorsingnalen en de stroom/ground worden direct aan de flight controller doorgegeven en dit met slechts 12 gr!
Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack Beschikt over betaflight osd en een 4S lipo kun je er direct op aansluiten. Tevens beschikt de flightcontroller over intern 16mb flash geheugen voor je blackbox.
De Lumenier MICRO LUX V3 komt met BetaFlight pre-installed. De Lumenier MICRO LUX supports ondersteunt zowel SBUS, PPM en DSMX ontvanger met zowel 5v als 3.3v support.
Note: The target for the LUX has the gyro mounted 90 degrees offset on the yaw axis. To correct this simply connect the FC to BetaFlight, and on the Configuration tab under “Board and Sensor Alignment” set the “Yaw Degrees” to “90” and save. Test the board’s movement in the configurator again to confirm correct orientation.
Lumenier Micro LUX V3 F4 Flight Controller
Kenmerken
- 2-4S Direct Lipo input support (5-16v)
- On-board BetaFlight OSD
- On-board 5v/2A and 3.3v/0.2A regulators
- SBUS and PPM support
- RGB LED dedicated pad, Current Sensor pad and Buzzer Pad
- VBAT Monitoring support
- 3x UART Ports
- Betaflight support (Supports new DSHOT protocol)
- BLHeli pass-through flashing supported by hardware
- Black box (flash memory to 16MB)
Specificaties
- STM32F405 (2MB flash) 32-bit processor
- MPU6000 Gyro/Accelerometer
- High quality 1.6mm PCB
- Micro USB connector for programming
- Dimensions: 27x27x6mm (includes USB in height)
- Mounting Holes: 20mm square to center of holes
- Weight: 4g
Lumenier BLHeli_32 30A 4S 4IN1 ESC
Kenmerken
- New 32bit Cortex-M0 running at 48MHz
- Latest Gen. firmware using BLHeli_32
- 2-4s LiPo battery compatible
- 30A per channel, 40A burst
- Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
- Lightweight, and compact size
- Adaptive timing, compatible with a wide range of motors and Kv
- Synchronous rectification technology adds efficiency, damped light
- Powerful regenerative braking / active braking.
Specificaties
- Input: 2-4s LiPoly
- Constant: 30 Amps (per channel)
- Burst: 35Amps (per channel)
- BEC: No
- Dimensions: 33x36mm(including the power pads)
- Mounting Holes: 20mm square to center of holes
- Weight: 8g (without motor wires)
User Manual
- Download the Micro LUX V3 Stack User Manual here.
- The MICRO LUX V3 uses the LUXF4OSD target. Download Betaflight Configurator here.
Inclusief
- 1x Lumenier MICRO LUX V3 F4 + 30A BLHeli_32 4in1 Stack
- Lumeneir LUX F4 + OSD Flight Controller (Designed for BetaFlight)
- Lumenier 30A BLHeli_32 4in1 ESC (2-4s)
- 1x Set of plastic mounting hardware
- 4x M3x20 screws, 4x 5mm spacer, 4x 3mm spacer, 4x nuts
- 1x 330uF 25v Low ESR Capacitor
- 1x Set 16awg silicone power wire (90mm)